Electrolux Professional New Zealand and Pacific Islands
Warewashing green&clean dual rinse rack type dishwasher with Steam abatement, 200r/h, electric,50Hz (Marine) (COD CC0FVZ)
Where to buy
Warewashinggreen&clean dual rinse rack type dishwasher with Steam abatement, 200r/h, electric,50Hz (Marine)
Dual Rinse Rack Type dishwashers - 200 racks per hour

Warewashing
green&clean dual rinse rack type dishwasher with Steam abatement, 200r/h, electric,50Hz (Marine)

COD CC0FVZ

Dual rinse rack type dishwasher, 200 racks/hour, Energy Saving Device, CLEAR BLUE Filtering System, electric, touch screen, customized direction on-site, USPH compliant, 50Hz - Marine

Where to buy

Specifications

  • Air humidity (top, exit): 100 / 0 % r.h.

    Latent heat: 4100 W

    Sensible heat: 2600 W

    Air flow (top, exit): 565 / 0 m³/h

    Air temperature (top, exit): 25.5 °C

    The data is measured at exhaust points at 25°C and 60% r.h. ambient conditions, 18°C inlet water temperature and refer only to the machine.

    This model requires a ventilation hood. Please refer to the attached "Recommended Exhaust Hood Design".

  • When the machine is run at DIN 10510 compliant speed.

    Pre-wash tank heating element are activated only during sanitation cycle.

    Supply voltage: 400 V/3 ph/50 Hz

    Pre-wash tank heating elements: 7 kW

    Default Installed Power: 42.5 kW

    Boiler heating elements: 20 kW

    Pre-wash pump size: 0.37 kW

    Electrical power min: 22.5 kW

    Wash pump size: 1.2 kW

    Wash tank heating elements: 20 kW

  • Inlet cold water line size: G 3/4"

    Inlet water supply temperature, pre-wash: 10-30°C

    When below 7°fH/4°dH special detergent and rinse aid are needed.

    Peak rate of drain flow: 2.5 l/s

    Pre-wash tank size: 35 l

    Wash tank size: 70 l

    Inlet hot water line size: G 3/4"

    Drain line size: 50mm

    Inlet water supply pressure: 1.5-6 bar

    Inlet Water Supply temperature (Steam abatement): 5 - 10 °C

    Inlet water supply temperature (wash and rinse): 50 - 65°C

    Inlet water supply hardness: 14 °fH / 8°dH

  • For transportation purpose only, the depth can be reduced to either 895mm by removing the main switch button or 797mm by removing the control box and the door handle.

    Reference norm used to measure the noise: IEC60335-2-58 annex AA.

    Table to table distance: 1680 mm

    Height with door open: 2095 mm

    Charging hole size (width): 530 mm

    Rinse temperature: 86 °C

    Productivity per hour (max. speed): 200 racks/3600dishes

    Productivity per hour (medium speed): 148 racks/2664 dishes

    External dimensions, Width: 2080 mm

    External dimensions, Depth: 925 mm

    External dimensions, Height: 1908 mm

    Productivity per hour (DIN compliant speed): 95 racks/1710 dishes

    Charging hole size (height): 490 mm

    Pre-wash temperature: 10-40°C

  • Noise level: <62 dBA

    Rinse water consumption at max speed: 0.9 l/rack

Product Features

Dual rinse technology ensures maximum rinse water covering every corner of the rack inside the rinse area for perfect hygiene on washed wares.
Automatic drain, clean and sanitize cycles featured as standard. The internal chamber, is completely cleaned or sanitized avoiding bacteria proliferation for maximum hygiene and reducing manual work/time for operator.
USPH performance compliant.
The unit is ready to be connected with OnE Connectivity for 24/7 real time monitoring, increasing equipment uptime, maximum profit and optimizing your process.
Three conveyor speeds can be selected through the control panel by the operator and customized on-site.
Built-in Steam Abatement using chilled water to absorb the hot steam generated by the machine thus releasing dry and fresh air to the dishwashing area.
Unit equipped with USB port making it simple to read data such as machine identification, counters and consumption, components, devices and alarm logs. Machine parameters can be uploaded and downloaded and firmware updated.
Intuitive touch screen control panel features user-friendly display to easily operate the machine and to monitor machine status. Three different levels of interaction are available each show relevant messages and information to the operator, the general maintenance staff and the authorized service partners.
Pre-wash section uses cold water so food remains are not "baked" onto the plates in order to have better pre-wash performance.
Maximum capacity per hour of 200 racks easy to switch to DIN 10510 compliant or other speed.
Adjustable feet for full access underneath the machine for cleaning.
Large counter balanced inspection door allow unrestricted all-round access to the wash and rinse area. Door is insulated with injected foam. This adds strength as well as reduces noise and heat loss.
All internal components: wash and rinse arms, tank filters, curtains can be easily removed for cleaning.
CLEAR BLUE filtering system removes soil from the wash water providing cleaner water and highly active detergent thus ensuring better washing performance and lower running costs.
Built-in drain valve in the tanks allows automatic dump and fill to refresh the water in the tank without any interruption of the washing process.
IP25 protection against water jets, solid objects and small animals (larger than 6 mm).
All main components made in heavy duty anti-corrosive 304 type stainless steel: external front, side panels and internal chambers, wash and rinse arms, doors and rack transportation system.
External pre-arrangement for inlet water, drain water, detergent & rinse aid connections for fast and easy installation on both sides of the unit.
Modularity design allows the machine not only be disassembled for delivery and re-assembled at customer’s site, but also to be customized and upgraded on-site and over time.
Dishwasher structure is held together with a solid 50 x 50 mm stainless steel frame to provide long-term sturdiness.
All electric components are put in one IP65 central box isolated from water and steam to ensure high reliability.
Deep drawn pressed wash tank with fully rounded corners, sloped towards the drain to prevent dirt buildup, provides fast drainage in just a few minutes. With no welding points the pressed tank offers a guaranteed water tight solution.
The unit is designed for marine application as components is easily accessible from front for service and maintenance without removing the machine.

Complete the form below to request more information

Select your country

 

Global

Global

Americas

North America

América Latina (Español)

Brasil

Middle East & Africa

Middle East & Africa (English)

Asia-Pacific

South East Asia and India (English)

Malaysia (English)

Australia

中国

日本

New Zealand and Pacific Islands

Europe

België

Belgique

Česká Republika & Slovenská Republika

Danmark

Deutschland

Österreich

Eesti

España

France

Ελληνικά

Hrvatska

Italia

Magyarország

Nederland

Norge

Polska

Schweiz

Suomi

Sverige

Türkiye

UK & Ireland

CIS

Armenia, Azerbaijan, Georgia, Kazakhstan, Kyrgyzstan, Moldova, Ukraine, Uzbekistan (English)

Your browser is out-of-date!

Update your browser to view this website correctly. Update my browser now

×